Anti-coking and anti-carburizing behavior of amorphous AlPO4 coating

The aim of the present study was to examine the anti-coking and anti-carburizing behavior of amorphous AlPO₄ coating. So, aluminum phosphate composition was synthesized by sol-gel process and applied on the AISI 304 stainless steel by dip coating technique. Anti-coking performance was examined in a tube furnace at 1000 °C for 30 min under Ethane (C₂H₆) atmosphere. Carburizing test was performed in a sealed charcoal medium at 1100 °C for a total of 30 h exposure time. Phase composition of the samples was analyzed by X-Ray Diffraction (XRD) after coking and carburizing tests. Scanning Electron Microscopy (SEM) and Energy Dispersive X-Ray Spectroscopy (EDS) were employed to study the morphology and elemental analysis of the samples after coke and carbon formation experiments. Microhardness indenter was applied on the cross section of the carbon-exposed specimens to plot the hardness profile through the carburizing zone. The results of the coking experiment revealed catalytic coke formed on the uncoated surface, while irregular spherical coke with no trace of catalytic coke was formed on the coated surface, indicating the great anti-coking performance of the amorphous AlPO₄ coating. The results of pack-carburizing test demonstrated that the thickness of the carbide layer formed on the bare surface was ～10 times greater than that of the coated sample. Hardness measurement for the amorphous AlPO₄ coated sample detected lower values compared to those for the uncoated one at all distances from the surface, indicating less carbon diffusion occurred beneath the coated surface. In overall, the results declared that the amorphous AlPO₄ coating could be a good candidate for surface protection of stainless steel against catalytic coke formation and carbon diffusion.     

Preparation of biphasic hydroxyapatite/ β-tricalcium phosphate foam using the replication technique

Biphasic hydroxyapatite/β-tricalcium phosphate foams were prepared using the replication technique starting from a precipitated hydroxyapatite (Ca₁₀(PO₄)₆(OH)₂: HAP) powder, and sodium glycerophosphate (GP). The effect of the grinding time, solid loading, dispersant amount, and etching, replication, and sintering processes were investigated. The SEM, OEM and FTIR analyses proved that the surface of the polyurethane template must be treated with NaOH solution to make it more hydrophilic prior to the coating process. With a solid loading of 40 wt-%, the slurries prepared from the precipitated hydroxyapatite presented a shear thinning behavior, which was useful for the coating process. The SEM analysis of the foams showed that the optimum number of coating layers to obtain foam with an identical structure with the template was limited to three. The use of GP and the optimized preparation parameters helped to decrease the consolidation temperature of the ceramic foams to 1000 °C. The XRD and FTIR analyses of the prepared foams showed that the thermal treatment of the GP and the HAP mixture led to a partial decomposition of the HAP to tricalcium phosphate. The fitting of the XRD patterns and the obtained lattice parameters proved that the decomposition was accompanied by the insertion of sodium from GP toward the lattice of tricalcium phosphate and the formation of Na-β-tricalcium. The results of the SEM analysis, the pore size distribution and the mechanical strength showed that the presence of the Na-β-tricalcium reduced the pore size distribution from 500-2700 to 100–1700 μm, decreased slightly the total porosity from 80 vol-% to 70 vol-%; and improved the mechanical strength of the obtained foam from 1.56 MPa to 2.60 MPa.     

Hydroxyapatite/tricalcium silicate composites cement derived from novel two-step sol-gel process with good biocompatibility and applications as bone cement and potential coating materials

Tricalcium silicate (C₃S) and hydroxyapatite (HAp) composites were fabricated through the sol-gel process. The aim of this research is to improve the biocompatibility of C₃S through HAp addition and study the potential of using this as coating materials. The composites (HAp/C₃S) were characterised by Fourier transform infrared spectrometry, thermal gravity-differential thermal analysis and X-ray diffraction. The working and setting times of cement pastes were tested using Gillmore needle. Mechanical properties were examined by nanoindentation and material testing system. In vitro biocompatibility of the materials were studied by cell attachment and viability of L929 and MG-63 cells. HAp/C₃S as a coating material on gelatin film were measured with the surface roughness and imaged by scanning electron microscope. With the addition of HAp, no undesirable free CaO was detected with the synthesis by the sol-gel preparation. The pH values of HAp added groups were between 7.54 and 8.76, which were much lower than pure C₃S group (pH?=?11.75). For in vitro studies, the presence of HAp could effectively enhance the cell attachment and viability of both L929 and MG-63 cells grown in the extract or directly on the composites. However, the mechanical properties of the composites were impaired as compared to pure C₃S. Lastly, HAp/C₃S cement could be evenly coated on gelatin film. HAp is successfully demonstrated to improve C₃S biocompatibility with this new composites HAp/C₃S. C-75 (75% C₃S and 25% HAp), in particular, has good biocompatibility, relatively high compressive strength and can be uniformly coated onto gelatin film. Thus, C-75 is a promising material for further investigation as a coating on other biopolymers.     

Dye removal by polymer derived ceramic nanobeads

Emulsion processed polymer derived ceramic (PDC) nanobeads are used for Methylene Blue dye removal from aqueous solutions. The PDC nanobeads, produced at 600 °C and 1200 °C pyrolysis, are subsequently coated with titania (anatase). Titania-coated nanobeads show less than 35%, i.e., limited dye adsorption capability in dark. Instead, enhanced total removal efficiency (∼97%) is obtained when the initial adsorption is succeeded by photodegradation under UV. Direct reusability tests show that even after the third cycle, very high regeneration efficiencies being above 92% are observed for titania-coated nanobeads.     

Tribological behavior of graphene reinforced chemically bonded ceramic coatings

To investigate tribological behavior of graphene reinforced chemically bonded ceramic coatings at different temperatures, tribological tests at room temperature, 200 °C and 500 °C were carried out. Results show that the fracture toughness and the hardness of the coating are improved with the introduction of graphene. Besides, the friction coefficient of the coating decreases with the addition of graphene at the room temperature and 200 °C. The coating without graphene achieves the similar friction coefficient at all temperatures. However, the coating with graphene achieves the lowest friction coefficient at 200 °C, and achieves the highest at 500 °C. In addition, the wear rate of the coating decreases with the increase of graphene. Besides, the wear rate at 200 °C is almost similar with that at room temperature. In contrast, the wear rate at 500 °C is much larger than those at room temperature and 200 °C. The mechanisms for graphene to decrease the friction coefficient and improve the wear resistance of chemically bonded ceramic coatings at evaluated temperatures are clarified.     

Influence of the ZrB2 content on the anti-oxidation ability of ZrB2-SiC coatings in aerobic environments with broad temperature range

ZrB₂-SiC coatings with different ZrB₂ contents were prepared by liquid phase sintering. The oxidation processes of coatings were explained according to TG results of ZrB₂-SiC coatings and powders tested from 298 K to 1773 K. Results show that, increasing ZrB₂ content made the weight of the samples changed from weight-loss of 10.04% to weight-gain of 0.14%, while the fastest weight-loss regions were narrowed, whose inflection points reduced from 1310℃ to 1050℃. Increasing ZrB₂ content made the relative oxygen permeability of the ZrB₂-SiC/SiC coatings reduced from 40%–60% to -10%-5%. Increasing ZrB₂ content enhanced high-temperature stability of coatings, making final weight of samples changed from weight-loss of 0.16% to weight-gain of 0.11% after oxidation at 1773 K for 200 h. The peeling and dispersion of Zr-oxides formed Zr-B-Si-O compound glass layer, presenting enhanced stability, dispersion strengthening and pinning effect of Zr-oxides, which were responsible for the excellent anti-oxidation protective effect of coatings in a broad temperature region.     

Effect of modified atmosphere packaging on the shelf-life of coated, whole and sliced mushrooms

Whole and sliced fresh mushrooms (Agaricus bisporus) were packaged with PVC wrap or two polyolefins (PD-941 and PD-961) films after coating with CaCl₂ and chitosan. Package gas composition, color, weight loss and maturity were measured during storage at 12 °C and 80%RH. For PD-961, the highest in-package concentration occurred during the first day of storage regardless of treatments, while wrap and PD-941 showed varying degrees in-package concentration with different processes and coatings. The whiteness of whole mushrooms varied significantly with the type of coating, but not with the type of films. The extent of darkening was greater in coated whole mushrooms than in sliced ones. Weight loss occurred in all packages and varied from 3 (g/100 g) to about 7 (g/100 g) after 6 days of storage. Due to a lower permeability, PD-961 packages had the lowest weight loss. The type of packaging films significantly affected the maturity index, where PD-961 most effectively lowered maturity index for both whole and sliced mushrooms, thus extending the shelf-life. The type of coating did not appear to affect maturity index except for the wrap package where chitosan coating markedly lowered the maturity index of sliced mushrooms.     

液相颗粒包裹法制备PbNb2O6微粉的研究

本文介绍了一种采用液相颗粒包裹技术制备功能陶瓷微粉的新方法.这种方法有如下特点:(1)方法简便,不需要特殊的设备,便于扩大应用于工业生产;(2)粉体颗粒尺寸小而均匀;(3)粉体化学组成偏离小、且均匀;(4)适应性强,从双组分至十多组分的材料微粉制备均可采用;(5)特别适用于一些含有难溶组分、用液相法无法制备的材料.本工作采用这一方法,成功地制备出 PbNb_2O_6微粉,其平均腰粒尺寸<0.5μm,分散性及化学均匀性好,烧结活性高,烧结温度可以降低近100℃,瓷坯密度可达理论密度的96%以上.     

中厚板轧制边部不均匀变形机理的探讨

通过分析宽中厚板轧制过程中的边部不均匀变形，探讨了其影响因素及大宽度板“切边纵裂”的产生原因，提出了解决问题的具体办法。